Choose the right ink type printer is extremely important to the durability of the machine. And when the ink runs out, how to refill. The following article will guide you to determine the type printing ink match and how to properly fill the printer ink. Stay tuned!
1. How to determine the right ink for the printer
To determine the right ink you need refer to the instructions Use of the machine, or ask carefully to know What model is my printer? From there determine the appropriate ink type.
Choose the right ink
The printer must not use proper or genuine ink, the components, the internal parts of the machine are easily damaged, causing you to incur additional repair costs.
Therefore, it is recommended to use the ink recommended by the manufacturer, so that the product has good ink quality and does not affect the durability of the machine.
2. Tools needed to refill ink
To save money you can refill the ink at home.
The device to refill the printer is quite simple and popular on the market as:
– Pointed pliers: Remove components from the print cartridge.
–Screw on screws 2 on both sides 4 sides and 2 sides (or 1-sided 4-sided): To disassemble the screw on the cartridge.
– Brushes: Clean the printer.
– Crochet or puncher: To grab the pins at both ends of the cartridge.
– A funnel: To refill the ink.
– 1 bottle of suitable ink.
Ink refill tool
In addition, you should prepare some additional items to clean the printer such as:
– Lubricants for cartridges.
– Wipes or soft paper to clean the components (do not use cotton to avoid cases when cleaning is trapped in the cartridge).
– Hygiene ball: Used to spray ink remaining on the cartridges and components during the refilling process.
3. Steps for refilling (refilling) print correctly
Before proceeding with refilling, you should Wear rubber or nylon gloves to protect your health, because ink is quite toxic.
You need to prepare the ink refills specified in section 2 and perform the following steps:
– Step 1: Remove the blank top panel
First, you look at the two sides of the cartridge will see a small white stainless steel pin (On the opposite side there is a similar white pin)> Use a screwdriver to gently trap 2 points 2 out.
Remove the blank parts
– Step 2: Remove the printer drum
Using a 4-sided screwdriver, tighten the two screws on the end of the gear gear side> Remove the drum head.
If the cartridge is new, not loaded at any time, there will be a sticker on top of a screw. Therefore, attention should be taken to remove 2 screws.
Then, you gently, carefully remove the empty drum, to not damage, reduce print quality
Remove the drum printer drum
Note: The cartridge is empty for the first time latches will be difficult to draw from the outside, so we need to proceed to remove the cartridge as follows:
First, remove 2 screws at the top of the drum> Remove the cover at the top of the drum> Remove the drum drum> Remove the rubber shaft.
Then, use a small 2-sided screwdriver to push the pin from the inside out, when the pin is pushed out, we should use the pointed pliers to pull out.
– Step 3: Refill the ink, clean the brush and rubber shaft
Waste toner is the amount of excess ink that is flicked to the top and down during the process of creating printed tables, which will eventually fill the ink reservoir.
You perform excess ink spill as follows:
Remove the drum> Remove the high-pressure shaft (rubber shaft, charging shaft)> Unscrew the 2 screws on the large brushed section> Empty the waste toner container from the waste toner container (located underneath the large brushed lever).
After emptying excess ink, wipe off the ink and rubber roll with a dry paper, or a dry towel.
Discard excess ink
– Step 4: Load new ink
After removing the excess ink, you clean the device components, check the machine parts.
Similar to the ink tray, you proceed to remove the ink spill cover and proceed to refill the ink. You can use hopper to prevent ink from spilling out.
Refill the ink cartridge
Note: Before proceeding to refill with ink cartridges, the table needs shake the toner so that the ink does not settle and clump.
– Step 5: Pair 2 cartridges
You proceed to pair the 2 parts of the cartridge together
Perform latching on both sides> Insert the spring to pull the 2 pieces together and clean through the outside of the cartridge.
Pair 2 cartridges
– Step 6: Insert the toner cartridge into the machine and print the checks
Finally you Reinstall the cartridge Go to the machine and print a test copy to check if there is anything abnormal.
If the print board is not blurred, not sticky, no more black dots, the ink pouring process is complete and effective, we can use normally without any problems.
Install the cartridge into the printer
So, Mobile World showed you how to choose the right ink and the steps to refill the printer.
If you have any questions, leave a comment immediately for instructions!
